What causes a washing machine not to drain and spin?

If the washer won't drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken. If a washer won't drain or spin, the fix is simple if you're even just a little bit handy with tools.
Takedown request   |   View complete answer on familyhandyman.com


How do you fix a washing machine that won't drain or spin?

What to Do When Your Washing Machine Won't Drain
  1. Perform a Master Reset. Unplug your washer for about one minute. ...
  2. Test the Lid Switch Assembly. ...
  3. See if the Drain Hose is Kinked. ...
  4. Check the Drain Hose or Pump for Clogs. ...
  5. Clean out the Coin Trap. ...
  6. Check the Water Level Control. ...
  7. Schedule Washing Machine Repair.
Takedown request   |   View complete answer on mrappliance.com


Why does my washing machine not rinse and spin?

There could be a variety of problems causing the rinse cycle not to work, including a broken or clogged drain pump, a bent or clogged drain hose, or a broken switch assembly.
Takedown request   |   View complete answer on blog.puls.com


Why are my clothes too wet after the spin cycle?

Loading Too Many Items

Overloading can lead to an imbalance that reduces the washer's spin speed, leaving clothes too wet after spin cycle completes. If the washer leaves clothes soaked after a large load, remove some items, redistribute others and run another rinse and spin cycle.
Takedown request   |   View complete answer on avivservicetoday.com


How do I know if my drain hose is clogged?

An easy way to check that the drain hose is clear is to blow air through it. If nothing is obstructing the drain tube, the problem is most likely at the washing machine pump. If the hose is worn or badly kinked, replacing the hose may improve the ability of the machine to pump water.
Takedown request   |   View complete answer on thespruce.com


What to do if your washer won't drain (Bosch Axxis models only)



Why does water stay in washing machine drum?

Water In Bottom of Washing Machine Drum: Why It Happens

Your drain hose is kinked. Your lid mechanism is broken or not engaging fully. Your drain or hose is clogged. Your load was too large for a good spin cycle.
Takedown request   |   View complete answer on blog.rentacenter.com


How do you manually drain a washing machine?

If not, follow these steps:
  1. Step 1: Turn off the power and lay down towels.
  2. Step 2: Locate the drain hose at the back of the washing machine.
  3. Step 3: Drain the water.
  4. Step 1: Turn off the power and lay down towels.
  5. Step 2: Locate the drain hose.
  6. Step 3: Drain the water.
  7. Step 4: Scrub the filter.
Takedown request   |   View complete answer on mrrooter.com


How do you drain a washer full of water?

How to drain a washer filled with water
  1. Try the spin cycle. ...
  2. Turn off the power and water supply. ...
  3. Remove and check the drain hose. ...
  4. Check to see if it will drain with the help of gravity. ...
  5. Check your machine's inner workings. ...
  6. Check the drain pipe. ...
  7. Drain manually if needed. ...
  8. Call a service professional.
Takedown request   |   View complete answer on cinchhomeservices.com


How do you tell if your washing machine is clogged?

If you notice persistent, pooling water in your washing machine unit following cycles and do not perform any regular drain inspections, there's a good chance your machine's drains have clogged over time due to everyday use.
Takedown request   |   View complete answer on expresssewer.com


How do you check if your washing machine is blocked?

How to unblock Your Washing Machine (8 Easy Steps):
  1. Turn your washing machine off at the plug. ...
  2. Locate the pump filter. ...
  3. Place a bucket, towel or even a baking tray under the pump filter. ...
  4. Unscrew the pump filter SLOWLY. ...
  5. Wait for the water to finish draining. ...
  6. Check to see if there is a block.
Takedown request   |   View complete answer on leydonlettings.co.uk


How much does it cost to replace a drain pump on a washing machine?

The most important part is a new washer pump. It can cost as little as $10 or as much as $75 or more. However, most homeowners pay between $25-$40 for a new pump.
Takedown request   |   View complete answer on homeadvisor.com


How do you test a drain pump?

Unscrew the screws with a Phillips screwdriver, and remove the panel by tilting it out while you lift it to unhook the top of the panel from the machine. You should see the drain pump attached to the bottom panel. It is connected to the drain hose.
Takedown request   |   View complete answer on homeguides.sfgate.com


How much does a washing machine pump cost?

The price of a new washing machine pump is $25 to $40 on its own, not including labor. When hiring a professional, repair prices range from $200 to $450.
Takedown request   |   View complete answer on homeadvisor.com


Will a blocked filter stop washing machine draining?

The job of the filter, which is located at the bottom front of the machine, is to prevent foreign objects from making their way to the washing machine pump and causing damage. However, if the filter isn't cleaned on a regular basis it can become blocked, preventing the appliance from draining.
Takedown request   |   View complete answer on blog.buyspares.co.uk


What's the average life of a washing machine?

Washing machines, on average, last around 10 years, according to Consumer Reports. If your washer is reaching the threshold, or it's been having some problems, here are some signs the end may be near.
Takedown request   |   View complete answer on cnet.com


Is it worth getting a washing machine fixed?

As a general rule, if it costs less than 50% of the price of a new washing machine to repair your old one, you should choose the repair option. But, you should also consider whether or not there is a warranty coverage on your washer and think about economic realities.
Takedown request   |   View complete answer on reliableappliancecs.com


Why are my sheets soaked after washing?

An Underpowered Spin

Unfortunately, if your washer has an underpowered spin, your items may not be spun fast enough to eliminate all the excess water. If you unload your washer and the items are soaking wet, yet there is no standing water in the machine, this is the most likely culprit.
Takedown request   |   View complete answer on universalappliancerepair.com


What is the difference between rinse and spin and drain and spin?

Rinse: The dirty, soapy water is drained, then the washing machine is refilled and your clothes are "rewashed" in clean water. Spin: All the water is drained completely, then your clothes are spun very fast and excess water is removed thanks to centrifugal force.
Takedown request   |   View complete answer on info.kensplumbing.net
Previous question
Where is India's biggest gym?
Next question
How do I secure my IP address?