How much grout should you remove when Regrouting?

Removing and replacing grout or “raking out” as it is known is not a nice job. Care must be taken to avoid damaging the tiles and it is very repetitive, The old grout must be removed to a depth of at least 2mm, preferably 3mm for re-grouting to work properly.
Takedown request   |   View complete answer on diydoctor.org.uk


Do you need to take out old grout before Regrouting?

You may not need to remove most of the grout. It may be possible to apply new grout over old grout without removing it at some places. However, where the grout has deteriorated heavily through crumbling or become too dirty, it is best to remove it before applying new grout.
Takedown request   |   View complete answer on groutmagnificent.com


How deep do you remove grout?

Your goal isn't to remove all the grout—only about 1/8 in. deep or so. Make several light passes until you reach the preferred depth. That'll be deep enough to embed the new grout.
Takedown request   |   View complete answer on familyhandyman.com


Can you put new grout over old grout?

You can apply new grout right over the top of the old grout. To do this, all you need is a grout removal tool. Use the tool to strike out the old grout, making sure the depth is at least 2mm, which is about the thickness of two dimes stacked one on top of the other.
Takedown request   |   View complete answer on tiledoctor.com


How much grout do I need to remove before caulking?

The tile grout should be scraped out with a Grout Getter about 1/8” to 3/16' below the top edge of the tile. This will allow enough room for the new grout to substantially fill in the grout joints. The old remaining grout in the joints will act as a good roughed-up bonding surface for the new grout to adhere to.
Takedown request   |   View complete answer on groutgetter.com


How to re-grout tiles



Is it OK to put caulk over grout?

Caulking over grout is only a temporary fix because caulk forms a poor bond with the more porous grout. Whether it takes a few months or a couple of years, the caulk will start to peel off the grout. Caulk over grout will peel off over time because caulk will not bond well with grout.
Takedown request   |   View complete answer on peppershomeandgarden.com


Do I need to remove grout before caulking?

If you decide to replace the grout with caulk, be sure that you remove all the existing grout with a grout saw, and then vacuum any remaining grout so you have a clean surface. Then you can apply the caulk and smooth it out with the tip of the caulk gun, the back of a spoon or your finger.
Takedown request   |   View complete answer on hunker.com


What happens if you put grout on top of grout?

Benefits of Putting New Grout Over Old Grout

Putting new grout over old grout is not as complicated as a complete re-grout as it does not require the removal of the old grout. It can also strengthen the surface to increase water resistance and make it less susceptible to impurities.
Takedown request   |   View complete answer on grout-experts.com


Should grout lines be flush with tile?

After the grout has been “cut off” the face, the next step is sponging the surface and tooling the joint. Tiles with a square edge need to have the grout finished flush with the tiled surface. Tiles with a cushion or radius edge should have the grout finished to the bottom of the cushion or radius.
Takedown request   |   View complete answer on tiledoctor.com


How often do you need to Regrout a shower?

For high traffic areas, like the main bathroom, you should consider sealing it every six months, while low traffic areas like the guest bathroom can be resealed every two years. If you are using epoxy grout, it might not be necessary to reseal it as it is highly water-resistant.
Takedown request   |   View complete answer on megasealed.com.au


What is the best tool to use to remove grout?

A reciprocating saw with a grout-removal attachment is one of the best ways to attack very tough grout, including sanded or epoxy-based grout. These powerful tools get the job done quickly and without creating too much dust, but you'll need to work carefully to avoid damaging surrounding tile.
Takedown request   |   View complete answer on thespruce.com


Can you use a drill bit to remove grout?

Grout provides a watertight seal and adds a finished appearance to the job. Occasionally you may need to replace a tile, which means you will have to remove the surrounding grout. You can do this with either a hand tool or a power tool with a specially designed drill bit.
Takedown request   |   View complete answer on ehow.com


Is it worth Regrouting tiles?

Regrouting can be a worthwhile home improvement project that keeps your floors looking good as new. It makes your tiles more resistant to mould, prevents water from seeping behind the shower floors and walls, and ensures they have a longer life span.
Takedown request   |   View complete answer on slique.com.au


How much does it cost to hire someone to Regrout tile?

Regrouting Tiles Cost

Homeowners, on average, spend between $250 and $1,000 to regrout 100 square feet of tile. Quotes can be as low as $170 or as high as $2,500.
Takedown request   |   View complete answer on homeadvisor.com


How deep should grout be between tiles?

Typically, we recommend grout joints being no less than a 1/8 of an inch however some precision cut tiles and stone can withstand a smaller grout joint. Grout joints also exist is to accommodate tiles that expand and contract during cooling and heating cycles.
Takedown request   |   View complete answer on conestogatile.com


Can grout be too low?

"Low Grout Joints" are defined as not being up to the top edge of the tile or cushioned edge, depending on the profile. Some of the problems leading to low grout joints include, Joints that aren't filled properly during application. Using too much water and washing the grout out of the joints.
Takedown request   |   View complete answer on ceramictilefoundation.org


Can you touch up grout after it dries?

Generally, you should be okay to mix up some grout and touch up any trouble spots in your new grout. Stuff like pin holes, scratches or low spots can be touched up with fresh grout the next day. The trick is to blend in the new grout with the old so make sure you mix it the same way that you mixed it the day before.
Takedown request   |   View complete answer on tilersplace.com


How do you fix uneven grout lines?

  1. Pour the grout mix on the tiles. ...
  2. Spread it out using the grout float. ...
  3. Don't try to cover the whole surface at a time. ...
  4. Drive grout into all the gaps with your float.
  5. Sweep diagonally across the tiles when removing excess grout. ...
  6. Remove as much as possible with the float and wait a few minutes.
Takedown request   |   View complete answer on cohesivehomes.com


How do you smooth grout lines?

  1. Fold a piece of medium-grit sandpaper to form a narrow sanding edge, then carefully sand back and forth in the grout joint without touching the tiles on either side.
  2. Sand with an angled foam sanding pad, using the thin edge to rub gently back and forth along the grout line.
Takedown request   |   View complete answer on hunker.com


Can you put silicone over cracked grout?

Can You Put Silicone Over Cracked Grout? You can put silicone caulk over cracked grout as a temporary solution, though it's not generally recommended. Silicone caulk will not hold well over the grout for an extended period of time, as it's not meant to bond to it.
Takedown request   |   View complete answer on homedecorbliss.com


Is it better to caulk or grout shower corners?

Grout, which is a cement-based material, is great for filling the spaces between tiles. But it isn't flexible enough to stay intact where a shower pan or tub meets surrounding walls. Nor is grout the right material for filling the corner joints on the walls. For these spaces, the right material is caulk.
Takedown request   |   View complete answer on washingtonpost.com


Is it better to caulk or grout around tub?

Since you are joining two different materials together, you should use caulk in the space where the floor tile and tub meet. Grout is not flexible, so it's not the best material for the job, while caulk allows for movement and also provides a better sealant.
Takedown request   |   View complete answer on abchomeandcommercial.com
Previous question
What happened Gillette?